U型螺栓,即骑马螺栓,骑马螺栓英文名称为U-bolt,是非标准件,是形状为U形所以也称为U型螺丝,U型管卡,U型管夹,两头有螺纹可与螺帽结合,主要用于固定管状物如水管或片状物如汽车的板簧。那u型螺栓等紧固件标准就是规范,每个国家和部门都有自己的标准。目前,我们在平时的业务中最常用到的标准有以下几种:
GB—中国国家标准(国标)ANSI—美国国家标准(美标)
DIN—德国国家标准(德标)ASME—美国机械工程师协会标准
JIS—日本国家标准(日标)BSW—英国国家标准
GB—国家标准是我国众多标准中的一种,另外还有行业标准,专业标准和部门标准等。国家标准又分:GB(强 制性标准)和GB/T(推荐性标准)以及GBn(国家内部标准)等。我们平常看到的像GB30,GB5783等等都是强制性的标 准。
以上几种标准除了一些基本尺寸如头部对边、头部厚度等的不同以外,最主要的是螺纹部分的不同。GB、DIN、JIS 等的螺纹都有是以MM(毫米)为单位,统称为公制螺纹。另像ANSI、ASME等的螺纹是以英寸为单位的称为美标螺纹。除 了公制螺纹和美制螺纹外还有一种BSW—英制标准,其螺纹也是以英寸为单位,俗称惠氏螺纹。
公制螺纹是以MM(毫米)为单位,它的牙尖角为60度。美制螺纹和英制螺纹都是以英寸为单位的。美制螺纹的牙尖角 也是60度,而英制螺纹的牙尖角为55度。由于计量单位的不同,导致了各种螺纹的表示方法也不尽相同。例如像M16- 2X60表示的就是公制的螺纹。他的具体意思是表示该螺丝的公称直径为16MM,牙距为2MM,长度为60MM,又如: 1/4—20x3/4表示的就是英制的螺纹,他的具体意思是该螺丝的公称直径为1/4英寸(一英寸=25.4MM),在一英 寸上有20个牙,长度为3/4英寸。另外要表示美制螺丝的话一般会在表示英制螺丝的后面加上UNC以及UNF,以此来区别 是美制粗牙或是美制细牙。
在平时的内销业务中,我们最常遇到的标准是GB(国标)和DIN(德标)。
在非芳生产品方面,主要会接触到以下几种标准:GB30;GB5783;GB5782;GB52;GB6170;GB818;GB819;GB845 ;GB846;GB70;DIN912;DIN933;DIN931等。目前GB30(老国标)在标准书中已被GB5783(新国标)所代替。GB52( 老国标)在标准书中已被GB6170(新国标)所代替。
在1986年,我们国家对标准件制定了新标准,在业务中一般俗称为新标,使用最多的主要有GB5780、GB5781、 GB5782、GB5783、GB5784。GB5780为六角头粗杆半牙螺丝,其精度等级为C级产品,可用GB5782来代替(GB5782为六角 头粗杆全牙螺丝,其精度等到级为A级和B级。)GB5781为六角头全牙螺丝,精度等级为C 级产品。可用GB5783来代替( GB5783为六角头全牙螺丝,其精度等级为A级和B 级)。GB5784为细杆半牙的六角螺丝。
新标与老标的区别在于:M8、M10、M12、M14、M22系列的产品,在对边宽度上有所区别。除M22系列的新产品外,新 标产品M8、M10、M12、M14的头部对边比老标的对边要小1MM。分别为13、16、18、21MM ,而M22系列的新产品,新标 比老标的对边反而要大2MM,应特别注意。对于头部厚度,新标和老标之间略有差别,在要求不是非常严格的情况下可以 通用。
新标与德标的区别在于:M10、M12、M14、M22的产品规格,在对边宽度上有所差别。M10、M12、M14的头部对边新标 比德标要小1MM。而M22的新产品的,其头部对边比德标的对边宽度要大2MM ,其它的均可通用。
标准件国家标准对照表
| 序号 | 德国标准 | 国际标准 | 中国标准 | 英文品名 | 中文品名 |
| Item | DIN-Standard | ISO-Standard | GB-Standard | DescriptioninEnglish | DescriptioninChinese |
| 1 | DIN1 | ISO2339 | GB117 | taperpins | 圆锥销 |
| 2 | DIN7 | ISO2338 | GB119-86 | parallelpins | 圆柱销 |
| 3 | DIN84 | ISO1207 | GB65-85 | slottedcheeseheadscrews | 开槽圆柱头螺钉 |
| 4 | DIN85 | ISO1580 | GB67-85 | slottedpanheadscrews | 开槽盘头螺钉 |
| 5 | DIN93 | GB854 | tabwashers | 单耳止动垫圈 | |
| 6 | DIN94 | ISO1234 | GB91 | splitcotterpins | 开口销 |
| 7 | DIN95 | GB101 | slottedraisedcskheadwoodscrews | 开槽半沉头木螺钉 | |
| 8 | DIN96 | GB99 | slottedroundheadwoodscrews | 开槽半圆头木螺钉 | |
| 9 | DIN97 | GB100 | slottedcountersunkheadwoodscrews | 开槽沉头木螺钉 | |
| 10 | DIN125-A | ISO7089 | GB97.1-85 | plainwashers | 平垫 |
| 11 | DIN125-B | ISO7090 | GB97.2-85 | mediunwashers | 平垫(带倒角) |
| 12 | DIN126 | ISO7091 | plainwashers | 平垫 | |
| 13 | DIN127-A | GB7244 | springlockwashers,tangends | 重型弹垫 | |
| 14 | DIN127-B | GB93-87 | springlockwashers,squareends | 标准弹垫 | |
| 15 | DIN128-A | GB7245-87 | singlecoilspringlockwashers | 鞍形弹垫 | |
| 16 | DIN137-A | curvedspringwashers | 弹簧止动垫圈 | ||
| 17 | DIN137-B | GB955 | wavespringwashers | 波形弹垫 | |
| 18 | DIN186 | GB37-88 | T-headboltswithsquareneck | T型方颈螺栓 | |
| 19 | DIN188 | T-headboltswithdoublenip | T型双接头螺栓 | ||
| 20 | DIN258 | ISO8737 | taperpinswiththreadedend | 螺纹圆锥销 | |
| 21 | DIN261 | T-headbolts | T型头螺栓 | ||
| 22 | DIN315AF | wingnutsamerciaform | 蝶型螺母(美制) | ||
| 23 | DIN315DF | GB62-88 | wingnutsgermanyform | 蝶型螺母(德制) | |
| 24 | DIN316AF | wingscrewsamerciaform | 蝶型螺钉(美制) | ||
| 25 | DIN317DF | wingscrewsgermanyform | 蝶型螺钉(德制) | ||
| 26 | DIN319 | ballknobs | 圆球型盖型螺母 | ||
| 27 | DIN404 | GB832-88 | slottedcapstanscrews | 开槽带孔球面圆柱头螺钉 | |
| 28 | DIN417 | ISO7435 | GB75-85 | slottedsetsrewswithfulldogpoint | 开槽长圆柱端紧定螺钉 |
| 29 | DIN427 | ISO2342 | GB73-85 | slottedsetsrewswithchamferedend | 开槽平端紧定螺钉(半牙) |
| 30 | DIN431 | GB808-88 | pipenutswiththread | 小六角特薄细牙螺母 | |
| 31 | DIN432 | GB856-88 | externaltap | 外舌止动垫圈 | |
| 32 | DIN433 | ISO7092 | GB848-95 | washersforcheeseheadscrews | 小垫圈(用于圆柱头螺钉) |
| 33 | DIN434 | GB852-88 | squaretaperwashersforU-section | 方斜垫圈(U型) | |
| 34 | DIN435 | GB852-88 | squaretaperwashersforI-sections | 方斜垫圈(I型) | |
| 35 | DIN436 | squarewashers | 方垫圈 | ||
| 36 | DIN438 | ISO7436 | GB74-85 | slottedsetwithcuppoint | 开槽凹端紧定螺钉 |
| 37 | DIN439 | ISO4035 | GB6172-86 | hexagonthinnuts | 六角薄螺母 |
| 38 | DIN439 | ISO8675 | GB6173-86 | hexagonthinnuts | 细牙六角薄螺母 |
| 39 | DIN440 | ISO7094 | roundswashersforwoodconstructions | 木螺钉专用垫圈 | |
| 40 | DIN443 | sealingcaps,push-intype | 密封帽 | ||
| 41 | DIN444 | GB798-88 | eyeboltsformB | 活节螺栓B型 | |
| 42 | DIN462 | internaltabwashers | 内舌止动垫圈 | ||
| 43 | DIN463 | GB855-88 | washerswithtwotaps | 双耳止动垫圈 | |
| 44 | DIN464 | GB834-88 | knurledthumbscrewswithcollar | 滚花高头螺钉 | |
| 45 | DIN465 | slottedknurledthumbscrewswithcollar | 开槽滚花高头螺钉 | ||
| 46 | DIN466 | GB806-88 | knurledthumbnutswithcollar | 滚花高螺母 | |
| 47 | DIN467 | GB807-88 | knurledthumbthinnuts | 滚花薄螺母 | |
| 48 | DIN470 | sealingwashers | 锁紧垫圈 | ||
| 49 | DIN471 | GB894.1-86 | retainingringsforshafts(external),circlips | 轴用弹性挡圈 | |
| 50 | DIN472 | GB893.1-86 | retainingringsforbores(internal),circlips | 孔用弹性挡圈 | |
| 51 | DIN478 | squareheadboltswithcollar | 方头带垫螺栓 | ||
| 52 | DIN479 | squareheadboltswithhalfdogpoint | 方头圆柱底端螺栓 | ||
| 53 | DIN480 | squareheadboltswithcollar,halfdog pointandroundedend | 方头带垫半圆底端螺栓 | ||
| 54 | DIN508 | ISO299 | T-slotnuts | T型槽螺母 | |
| 55 | DIN525 | singleendstuds | 单头螺柱 | ||
| 56 | DIN529 | GB799-88 | masonrybolts | 地脚螺栓 | |
| 57 | DIN546 | GB817-76 | slottedroundnuts | 带槽圆螺母 | |
| 58 | DIN547 | GB815-88 | roundnutswithdrilledholesinoneface | 端面带孔圆螺母 | |
| 59 | DIN551 | ISO4776 | GB73-85 | slottedsitscrewswithflatpoint | 开槽平端紧定螺钉 |
| 60 | DIN553 | ISO7434 | GB71-85 | slottedsetscrewswithconepoint | 开槽锥端紧定螺钉 |
| 61 | DIN555 | ISO4034 | hexagonnuts | 六角螺母 | |
| 62 | DIN557 | GB39-88 | squarenuts | 方螺母-C | |
| 63 | DIN558 | ISO4018 | hexagonscrews | 六角头螺钉 | |
| 64 | DIN561 | hexagonsetscrewswithfulldogpoint | 六角头圆柱端紧定螺钉 | ||
| 65 | DIN562 | squarenutswithoutbevel(pressednuts) | 薄型方螺母-B | ||
| 66 | DIN571 | GB102-86 | hexagonheadwoodscrews(coachscrews) | 六角头木螺钉 | |
| 67 | DIN580 | ISO3266 | GB825-76 | liftingeyebolts | 吊环螺钉 |
| 68 | DIN582 | liftingeyenuts | 吊环螺母 | ||
| 69 | DIN601 | ISO4016 | hexagonbolts | 六角头螺栓 | |
| 70 | DIN603 | ISO8677 | GB14-88 | mushroomheadsquareneckbolts (carriagebolts) | 大半圆头方颈螺栓(马车螺栓) |
| 71 | DIN604 | flatcountersunknibbolts | 沉头带插销马车螺栓 | ||
| 72 | DIN605 | flatcountersunklongsquare neckbolts | 沉头长方颈马车螺栓 | ||
| 73 | DIN607 | cupheadnibbolts | 半圆头带插销马车螺栓 | ||
| 74 | DIN608 | flatcountersunkshortsquareneckbolts | 沉头短方颈马车螺栓 | ||
| 75 | DIN609 | hexagonfittedbolts,longthread | 六角头精配螺栓(长螺纹) | ||
| 76 | DIN610 | hexagonfittedbolts,shortthread | 六角头精配螺栓(短螺纹) | ||
| 77 | DIN653 | GB835-88 | knurledthumbscrewsthintype | 滚花平头螺钉 | |
| 78 | DIN660 | ISO1051 | GB867-86 | roundheadrivets | 半圆头铆钉 |
| 79 | DIN661 | ISO1051 | GB869-86 | contersunkheadrivets | 沉头铆钉 |
| 80 | DIN662 | ISO1051 | raisedcontersunkheadrivets | 半沉头铆钉 | |
| 81 | DIN674 | ISO1051 | mushroomheadrivets | 大扁头铆钉 | |
| 82 | DIN703 | adjustingrings,heavyrange(shaftingcollars) | 重型侧面带孔圆螺母 | ||
| 83 | DIN705 | GB816-88 | adjustingrings,lightrange(shaftingcollars) | 侧面带孔圆螺母 | |
| 84 | DIN741 | wireropeclips | 卡头 | ||
| 85 | DIN787 | ISO299 | T-slotscrews | T型槽螺钉 | |
| 86 | DIN835 | GB900-88 | studs-metal(end=2d) | 双头螺柱(牙长=2D) | |
| 87 | DIN906 | hexagonsocketpipeplugs,conicalthread | 内六角锥型闭锁螺钉 | ||
| 88 | DIN908 | hexagonsocketscrewplugs,cyl.thread | 内六角直型闭锁螺钉 | ||
| 89 | DIN909 | hexagonheadpipeplugs,conicalthread | 外六角锥型闭锁螺钉 | ||
| 90 | DIN910 | hexagonheadscrewplugs,cyl.thread | 外六角直型闭锁螺钉 | ||
| 91 | DIN911 | ISO2936 | socketwrenches | 内六角扳手 | |
| 92 | DIN912 | ISO4762 | GB70-85 | hexagonsocketcapscrews | 内六角圆柱头螺钉 |
| 93 | DIN913 | ISO4026 | GB77-85 | hexagonsocketsetscrewswithflatpoint | 内六角平端紧定螺钉 |
| 94 | DIN914 | ISO4027 | GB78-85 | hexagonsocketsetscrewswithconepoint | 内六角尖端紧定螺钉 |
| 95 | DIN915 | ISO4028 | GB79-85 | hexagonsocketsetscrewswithdogpoint | 内六角圆柱端紧定螺钉 |
| 96 | DIN916 | ISO4029 | GB80-85 | hexagonsocketsetscrewswithcuppoint | 内六角凹端紧定螺钉 |
| 97 | DIN917 | hexagoncapnuts | 薄型盲螺母 | ||
| 98 | DIN920 | slottedshortcheeseheadscrews | 开槽小圆柱头螺钉 | ||
| 99 | DIN921 | GB838-88 | slottedlargecheeseheadscrews | 开槽大圆柱头螺钉 | |
| 100 | DIN923 | GB830-88 | slottedpanheadscrewswithshoulder | 开槽圆柱头轴肩螺钉 | |
| 101 | DIN927 | slottedshoulderscrews | 开槽无头轴肩螺钉 | ||
| 102 | DIN928 | GB/T13680-92 | squareweldnuts | 焊接方螺母 | |
| 103 | DIN929 | GB/T13681-92 | hexagonweldnuts | 焊接六角螺母 | |
| 104 | DIN931 | ISO4014 | GB5782-86 | hexagonheadscrews | 六角头螺栓(半牙) |
| 105 | DIN933 | ISO4017 | GB5783-86 | hexagonheadscrews | 六角头螺栓(全牙) |
| 106 | DIN934 | ISO4032 | GB6170-86 | hexagonfullnuts | 六角头螺母(1型) |
| 107 | DIN934 | ISO8673 | GB6171-86 | hexagonfullnuts | 细牙六角头螺母(1型) |
| 108 | DIN935 | ISO7035 | GB6178-86 | hexagonslottedandcastlenuts | 开槽六角螺母 |
| 109 | DIN936 | ISO4035 | GB6172.1-86 | hexagonthinnuts | 六角头薄螺母 |
| 110 | DIN937 | ISO7038 | GB6181-86 | hexagonthinslottedandcastlenuts | 六角头开槽薄螺母 |
| 111 | DIN938 | GB897-88 | studsmetal(end=1d) | 双头螺距(牙长=1D) | |
| 112 | DIN939 | GB898-88 | studsmetal(end=1.25d) | 双头螺距(牙长=1.25D) | |
| 113 | DIN940 | studsmetal(end=1.5d) | 双头螺距(牙长=1.5D) | ||
| 114 | DIN960 | ISO8765 | GB5785-86 | hexagonheadbolts,metricfinepitchthread | 六角头细牙螺栓(半牙) |
| 115 | DIN961 | ISO8676 | GB5786-86 | hexagonheadbolts,metricfinepitchthread | 六角头细牙螺栓(全牙) |
| 116 | DIN962 | additionalshapesandversionsforbolts | 头部穿孔六角头螺栓 | ||
| 117 | DIN963 | ISO2009 | GB68-85 | slottedcountersundheadscrews | 开槽沉头螺钉 |
| 118 | DIN964 | ISO2010 | GB69-85 | slottedraisedcountersunk ovalheadscrews | 开槽半沉头螺钉 |
| 119 | DIN965 | ISO7046 | GB819-85 | crossrecessedcount ersunkheadscrews | 十字槽沉头螺钉 |
| 120 | DIN966 | ISO7047 | GB820-85 | crossrecessedraisedcount ersunkheadscrews | 十字槽半沉头螺钉 |
| 121 | DIN970 | hexagonnutstype-1 | 六角头螺母 | ||
| 122 | DIN971 | hexagonnutstype-2 | 六角头螺母 | ||
| 123 | DIN972 | ISO8674 | GB6176-86 | hexagonnutswithfinethread | 细牙六角头螺母(2型) |
| 124 | DIN975 | GB15389-94 | threadedrods(studdings) | 牙条(全螺纹) | |
| 125 | DIN976 | threadedpins(studbolts) | 螺纹销 | ||
| 126 | DIN979 | hexagonthinslottedandcastlenuts | 六角头开槽薄螺母(2型) | ||
| 127 | DIN980 | ISO7199 | GB6184-86 | prevaillingtorquetypehexagonnuts, allmetallnuts | 全金属六角锁紧螺母(1型) |
| 128 | DIN981 | ISO2982 | GB812-88 | locknuts | 圆螺母 |
| 129 | DIN982 | ISO7040 | GB889.1-86 | prevaillingtorquetypehexagonnuts, heavytype,withnyloninsert | 六角头尼龙锁紧螺母 |
| 130 | DIN985 | ISO10511 | GB6172.2-86 | prevaillingtorquetypehexagonnuts, heavytype,withnyloninsert | 六角头薄型尼龙锁紧螺母 |
| 131 | DIN986 | prevaillingtorquetypedomedcapnuts withnyloninsert | 六角盖型尼龙锁紧螺母 | ||
| 132 | DIN988 | shimrings | 配合垫片 | ||
| 133 | DIN1052 | washersfortimberconnectors | 木材连接用垫片 | ||
| 134 | DIN1151 | roundplainheadnails | 沉头钢钉 | ||
| 135 | DIN1440 | ISO8738 | plainwashersforclevispins(A型) | 销钉专用垫片A型 | |
| 136 | DIN1441 | plainwashersforclevispins | 销钉专用垫片 | ||
| 137 | DIN1444 | ISO2341 | clevispinswithhead | 带头销钉 | |
| 138 | DIN1471 | ISO8744 | GB/T13829.2 | groovedpins,tapergrooved | 圆锥型槽销 |
| 139 | DIN1472 | ISO8745 | GB/T13829.2 | groovedpins,tapergroovedhalflength | 圆锥型槽销(半槽) |
| 140 | DIN1473 | ISO8740 | groovedpins,parallelgroovedfulllength | 平行槽销(带倒角) | |
| 141 | DIN1474 | ISO8741 | groovedpins,reservegroovedhalflength | 前端凹槽槽销 | |
| 142 | DIN1475 | ISO8742 | groovedpins,centregrooved | 中部凹槽槽销 | |
| 143 | DIN1476 | ISO8746 | GB/T13829.3 | groovedpinswithroundhead | 圆头槽销 |
| 144 | DIN1477 | ISO8747 | groovedpinswithcount ersunkhead | 沉头槽销 | |
| 145 | DIN1479 | turnuckles(centreparts), madeoutofhexagonbar | 六角螺母棒 | ||
| 146 | DIN1480 | turnuckleswitheyeboltandhookbolt | 花篮螺栓 | ||
| 147 | DIN1481 | ISO8752 | GB879-86 | springpins,heavytype | 弹性圆柱销 |
| 148 | DIN1587 | GB802-88 | hexagondomedcapnuts | 组合式盖型螺母 | |
| 149 | DIN1804 | slottedroundnutsforhookspanner | 开槽圆螺母(配合沟头扳手) | ||
| 150 | DIN1816 | roundnutswithsetholes | 圆螺母(带插销孔) | ||
| 151 | DIN2093 | discsprings | 盘型弹簧垫圈 | ||
| 152 | DIN3017 | hoseclamps | 喉箍 | ||
| 153 | DIN3404 | lubricatingnipples,buttonhead | 润滑油嘴(旋扭头) | ||
| 154 | DIN3567 | shacklesforconduilts | 管夹 | ||
| 155 | DIN3570 | stirrupbolts(U-bolts) | U型螺栓 | ||
| 156 | DIN6319 | GB849-88 | sphericalwashers,conicalseats | 球面垫圈 | |
| 157 | DIN6325 | ISO8734 | parallelpins | 圆柱销 | |
| 158 | DIN6330 | GB56-88 | hexagonnuts,1.5d | 厚六角螺母 | |
| 159 | DIN6331 | GB6177-86 | hexagonnuts,1.5dwithcollar | 厚六角法兰面螺母 | |
| 160 | DIN6334 | hexagonnuts,3d | 长六角螺母 | ||
| 161 | DIN6797-A | GB862.1-87 | externalteethlockwashers | 外齿锁紧垫圈 | |
| 162 | DIN6797-I | GB861.1-87 | internalteethlockwashers | 内齿锁紧垫圈 | |
| 163 | DIN6798-A | GB862.2-87 | externalteethserratedlockwashers | 外锯齿锁紧垫圈 | |
| 164 | DIN6798-I | GB861.2-87 | internalteethserratedlockwashers | 内锯齿锁紧垫圈 | |
| 165 | DIN6799 | GB896-76 | retainingringsforshafts(E-rings),circlips | 开口挡圈 | |
| 166 | DIN6885 | ISO773/2491 | parallelkeys(formA) | 平键(A型) | |
| 167 | DIN6888 | ISO3912 | woodruffkeys | 半圆键 | |
| 168 | DIN6899 | thimbles | 嵌环(支撑环) | ||
| 169 | DIN6900 | GB9074.1-.17 | screwsandwashersassemblies | 机器螺钉和垫圈组合件 | |
| 170 | DIN6901 | GB9074.18-.23 | tappingscrewsandwashersassemblies | 自攻螺钉和垫圈组合件 | |
| 171 | DIN6912 | hexagonsocketheadcap screwswithhole,lowhead | 薄型带孔内六角圆柱头螺钉 | ||
| 172 | DIN6914 | hexagonheadboltswithlarge head(frictiongripbolts) | 大六角头螺栓 | ||
| 173 | DIN6915 | hexagonnutswithlargewideth acrossflat(frictiongripnuts) | 大六角螺母 | ||
| 174 | DIN6916 | roundwashersforfrictiongripbolts | 大垫圈 | ||
| 175 | DIN6917 | spuaretaperwashersfor frictiongripboltsonT-sections | 楔型方垫圈 | ||
| 176 | DIN6923 | ISO4161 | GB6177-86 | hexagonflangenuts | 六角法兰面螺母 |
| 177 | DIN6925 | ISO7042 | GB6185.1-2000 | prevailingtorquetypehexagonnuts, allmetallicnuts | 全金属六角锁紧螺母(2型) |
| 178 | DIN7337 | GB12617/12618 | blindrivets | 开口型抽芯铆钉(沉头、扁圆头) | |
| 179 | DIN7338 | GB875/975-86 | rivetsforbrakeandclutchlining | 扁平头半空心/全空心铆钉 | |
| 180 | DIN7343 | ISO8750 | spiralpins | 螺旋夹紧销 | |
| 181 | DIN7346 | ISO13337 | springpins,lighttype | 轻型弹性圆柱销 | |
| 182 | DIN7349 | washersforboltswithheavytypespringpinss | 重型弹性圆柱销用垫圈 | ||
| 183 | DIN7500 | threadformingscrewsforISO-metricthread | ISO公制螺纹螺钉(多种头型) | ||
| 184 | DIN7504 | self-drillingtappingscrews | 自攻自钻螺钉(多种头型) | ||
| 185 | DIN7513 | threadcuttingscrews | 开槽切削螺纹螺钉(多种头型) | ||
| 186 | DIN7516 | threadcuttingscrewscrossrecess | 十字槽切削螺纹螺钉(多种头型) | ||
| 187 | DIN7965 | teenutswithpronge | T型四爪螺母 | ||
| 188 | DIN7968 | GB1228/1229/1230 | hexagonheadfittedboltsforsteelstructures | 钢结构用六角头螺栓连接副 | |
| 189 | DIN7971 | ISO1481 | GB5282-85 | panheadtappingscrewswithslot | 开槽盘头自攻螺钉 |
| 190 | DIN7972 | ISO1482 | GB5283-85 | countersunkflatheadtappingscrewswithslot | 开槽沉头自攻螺钉 |
| 191 | DIN7973 | ISO1483 | GB5284-85 | raisedcountersunkovalheadtappingscrewswithslot | 开槽半沉头自攻螺钉 |
| 192 | DIN7976 | ISO1479 | GB5285-85 | hexagontappingscrews | 六角头自攻螺钉 |
| 193 | DIN7980 | ISO8738 | springlockwashersforscrews withcylindricalheads | 圆柱头螺钉用弹簧垫圈 | |
| 194 | DIN7981 | ISO7049 | GB845-85 | panheadtappingscrews withcrossrecessed | 十字槽盘头自攻螺钉 |
| 195 | DIN7982 | ISO7050 | GB846-85 | countersunkflatheadtappingscrews withcrossrecessed | 十字槽沉头自攻螺钉 |
| 196 | DIN7983 | ISO7051 | GB847-86 | raisedcountersunkovalheadtappingscrews withcrossrecessed | 十字槽半沉头自攻螺钉 |
| 197 | DIN7984 | hexagonsocketheadcapscrewswith,reducedhead | 薄型内六角圆柱头螺钉 | ||
| 198 | DIN7985 | ISO7045 | GB818-85 | panheadscrewswithcrossrecessed | 十字槽盘头螺钉 |
| 199 | DIN7989 | GB1230-84 | washersforsteelstructures | 钢结构用垫圈 | |
| 200 | DIN7990 | GB1229-84 | hexagonheadboltsforsteelstructures | 钢结构用六角头螺栓 | |
| 201 | DIN7991 | ISO10642 | GB70.3 | hexagonsocketcount ersunkheadscrews | 内六角沉头螺钉 |
| 202 | DIN7993 | GB895.2-86 | roundwiresnapringsforshafts | 轴用钢丝挡圈 | |
| 203 | DIN7995 | GB952-86 | crossrecessedraisedcountersunkheadwoodscrews | 十字槽半沉头木螺钉 | |
| 204 | DIN7996 | GB950-86 | crossrecessedroundheadwoodscrews | 十字槽圆头木螺钉 | |
| 205 | DIN7997 | GB951-86 | crossrecessedcountersunkheadwoodscrews | 十字槽沉头木螺钉 | |
| 206 | DIN8140 | ciolinserts,coarse, finethread,silflocking | 螺纹护套(普通自锁等) | ||
| 207 | DIN9021 | ISO7093 | GB96-85 | washers,outsidediameterappro.3d | 大外径垫圈 |
| 208 | DIN11024 | springcotterforabolt | 弹簧卡子 | ||
| 209 | DIN13257 | beltingbolts(elevatorbolts) | 平板螺栓 | ||
| 210 | DIN18182 | drywallscrews | 干壁钉(墙板钉) | ||
| 211 | DIN28129 | GB63-88 | liftingnuts(eyenuts) | 环型螺母 | |
| 212 | DIN70952 | GB858-88 | tabwashersforslottedroundnuts | 圆螺母用止退垫圈 |
相关推举:
U型螺栓
QQ交流群
