型号 | 公称转 矩Tn/ kN·m | 许用径 向力 /kN | d (H7) | L | D | D1 | D2 (h6) | D3 | n-d1 | S (h9) | l1 | l2 | l3 | l4 | α /(°) | r | C | 磨损刻 度m1 | 转动惯 量I/ kg·m | 质量 m/kg | 孔 | 螺 栓 | WJA1 | 4 | 14.5 | 40,42,45,48 | 84 | 250 | 220 | 160 | 85 | 6-14 | M12 | 220 | 42 | 5 | 12 | 24 | 60 | 2 | 1.6 | 4 | 0.059 | 11.7 | 50,55 | WJA 2 | 5 | 16.5 | 45,48,50,55 | 84 | 280 | 250 | 180 | 90 | 6-14 | M12 | 250 | 42 | 5 | 12 | 24 | 60 | 2 | 1.6 | 4 | 0.093 | 14.7 | 60 | 107 | 2 | 14.5 | WJA 3 | 7.1 | 18.5 | 48,50,55 | 84 | 320 | 280 | 200 | 95 | 6-18 | M16 | 280 | 45 | 5 | 15 | 25 | 60 | 2.5 | 1.6 | 4 | 0.176 | 19.9 | 60,65 | 107 | 2 | 20 | WJA 4 | 9 | 20 | 60,65,70,75 | 107 | 340 | 300 | 220 | 130 | 6-18 | M16 | 300 | 45 | 5 | 15 | 25 | 60 | 2.5 | 2 | 4 | 0.253 | 27.1 | 80,85 | 132 | 26.9 | WJA 5 | 14 | 31 | 70,75 | 107 | 360 | 320 | 240 | 150 | 6-18 | M16 | 320 | 45 | 5 | 15 | 25 | 60 | 2.5 | 2 | 6 | 0.335 | 31.8 | 80,85,90,95 | 132 | 2.5 | 33.3 | WJA 6 | 18 | 35 | 80,85,90,95 | 132 | 380 | 340 | 260 | 160 | 6-18 | M16 | 340 | 45 | 5 | 15 | 25 | 60 | 2.5 | 2.5 | 6 | 0.451 | 39.4 | 100,110 | 167 | 39.8 | WJA 7 | 22.4 | 38.5 | 80,85,90,95 | 132 | 400 | 360 | 280 | 170 | 6-18 | M16 | 360 | 47 | 5 | 15 | 33 | 60 | 3 | 2.5 | 6 | 0.58 | 47 | 100,110,120 | 167 | 48 | WJA 8 | 28 | 42 | 100,110,120 | 167 | 420 | 380 | 310 | 200 | 6-18 | M16 | 380 | 47 | 5 | 15 | 33 | 60 | 3 | 2.5 | 6 | 0.91 | 66 | 130,140 | 202 | 3 | 64 | WJA 9 | 35.5 | 49 | 100,110,120 | 167 | 450 | 400 | 340 | 230 | 6-22 | M20 | 400 | 52 | 5 | 20 | 28 | 60 | 3 | 2.5 | 6 | 1.35 | 83 | 130,140,150 | 202 | 3 | 83.5 | WJA10 | 71 | 115 | 130,140,150 | 202 | 550 | 500 | 420 | 280 | 6-22 | M20 | 500 | 60 | 8 | 20 | 38 | 60 | 3 | 3 | 8 | 3.69 | 151 | 160,170,180 | 242 | 145 | WJA11 | 112 | 125 | 160,170,180 | 242 | 580 | 530 | 450 | 300 | 8-22 | M20 | 530 | 60 | 8 | 20 | 38 | 40 | 3 | 3 | 8 | 4.53 | 169 | 190,200 | 282 | 4 | 167 | WJA12 | 180 | 150 | 190,200,220 | 282 | 650 | 600 | 530 | 360 | 8-22 | M20 | 580 | 65 | 8 | 25 | 33 | 40 | 3 | 4 | 8 | 8.41 | 247 | 240,250 | 330 | 229 | WJA13 | 315 | 250 | 200,220 | 282 | 680 | 630 | 560 | 400 | 24-22 | M20 | 600 | 65 | 8 | 25 | 35 | 10 | 4 | 4 | 8 | 11.4 | 301 | 240,250,260 | 330 | 302 | WJA14 | 400 | 300 | 240,250,260 | 330 | 710 | 660 | 600 | 440 | 24-26 | M24 | 640 | 82 | 10 | 35 | 43 | 10 | 4 | 4 | 8 | 17.7 | 392 | 280,300 | 380 | 5 | 386 | WJA15 | 500 | 340 | 240,250,260 | 330 | 780 | 730 | 670 | 500 | 24-26 | M24 | 700 | 82 | 10 | 35 | 43 | 10 | 4 | 4 | 8 | 29 | 536 | 280,300,320 | 380 | 5 | 547 | WJA16 | 630 | 380 | 280,300,320 | 380 | 850 | 800 | 730 | 550 | 24-26 | M24 | 760 | 82 | 10 | 35 | 43 | 10 | 4 | 5 | 8 | 43.6 | 686 | 340,360,380 | 450 | 6 | 679 |
注:1.选用轴孔直径d和长度L在表列范围以外时,可与制造厂商定。 2.转动惯量和质量是按轴孔最小直径计算的近似值。 | |